Author |
Message |
rrpilot
|
Post subject: S&W 642? Posted: Mon Oct 06, 2008 2:09 am |
|
Joined: Sun Sep 07, 2008 11:17 pm Posts: 9 Location: Burnsville
|
Hi all,
If this has been covered before my apologies...I am the new owner of an S&W 642( Thanks Joel, great course!...."
Anyhow I was really dissapointed with the manual, it doesnt really seem to cover any upkeep issue's, mostly stuff such as "Never point a loaded gun at your head after consuming alcohol...LOL..."
Not making light, I know safety is #1, of course, but I was looking for tips on such things as upkeep?, where to oil after use?, and how to do that properly?
Any tips, greatly appreciated
Joe
_________________ Don't Panic
|
|
|
|
|
lumbering.buffalo
|
Post subject: Posted: Mon Oct 06, 2008 8:15 am |
|
Joined: Sat Apr 29, 2006 6:08 pm Posts: 267
|
I'm not the most fastidious keeper of guns, but here is what I do with my 642. Between shooting sessions: 1) After unloading and putting the cartridges in another location I run a patch through the barrel to get the dust bunnies out. 2) Push the ejector, q-tip moistened with oil on the "axle" and put it back. 3) wipe down with a silicon cloth, reload and holster.
After a shooting session I use the brass brush and Hoppe's #9 or gun scrubber in the cylinder and barrel followed by dry patches. Hoppe's or gun scrubber and plastic-bristle brush around the forcing cone, the front of the cylinder; anywhere there is soot. Wipe down with rag, oil in the before mentioned places and go.
Once in a while I will remove the grips, check, clean and lightly oil the springs.
Others may have a better method. I'm not one for removing screws and taking things apart as I'm not good at putting them back together again.
|
|
|
|
|
joelr
|
Post subject: Re: S&W 642? Posted: Mon Oct 06, 2008 8:29 am |
|
The Man |
|
Joined: Sun Aug 07, 2005 5:43 am Posts: 7970 Location: Minneapolis MN
|
rrpilot wrote: Hi all, If this has been covered before my apologies...I am the new owner of an S&W 642( Thanks Joel, great course!...." :) Quote: Anyhow I was really dissapointed with the manual, it doesnt really seem to cover any upkeep issue's, mostly stuff such as "Never point a loaded gun at your head after consuming alcohol...LOL..." Not making light, I know safety is #1, of course, but I was looking for tips on such things as upkeep?, where to oil after use?, and how to do that properly? Any tips, greatly appreciated Joe The 642 requires very, very little maintenance. You can easily get by, pretty much forever, by taking it outside (unloaded, of course, with the cylinder swung out) and spraying it with Powderblast, being sure to push on the ejector rod so the stuff can get in there, too. A quick wipedown with a paper towel, and that'll do it.
If you want to go a bit further (I do, m'self), put a small drop of something like Breakfree (or other good lubricant) on the ejector rod, and another on the crane hinge.
Now, some folks go through the whole routine with patches and Hoppes and all, and there's nothing wrong with that, either.
_________________ Just a guy.
|
|
|
|
|
mnglocker
|
Post subject: Posted: Mon Oct 06, 2008 10:31 am |
|
Longtime Regular |
|
Joined: Wed Jul 19, 2006 12:04 pm Posts: 1682 Location: Wright County
|
If you're shooting alot of lead you will need to clean the leading on the front of the cylinder. I usually use lead remover and a bronze phospor brush, followed by a quick wipe down with hoppes #9.
And IIRC do not use lead solvent/copper solvent on blued guns unless you want to reblue them.
_________________ Get Off My Lawn.
|
|
|
|
|
joelr
|
Post subject: Posted: Mon Oct 06, 2008 10:41 am |
|
The Man |
|
Joined: Sun Aug 07, 2005 5:43 am Posts: 7970 Location: Minneapolis MN
|
Yup. But the 642 isn't blued.
It's a typical (good) revolver: it takes a lot of crud to affect it.
_________________ Just a guy.
|
|
|
|
|
westhope
|
Post subject: Posted: Mon Oct 06, 2008 10:44 am |
|
Longtime Regular |
|
Joined: Tue Sep 06, 2005 10:11 am Posts: 572 Location: West of Hope, MN (S. Central MN)
|
DO NOT USE "GUNSCRUBBER!"
It will remove the clear coating over the anodized finish.
They require very little maintance. Just clean the bore and cylinders. Wipe down the outside with a silicon cloth. Wipe the stainless steel parts with a very lightly oiled cloth.
The internal working parts can be cleaned and oiled by removing the sideplate but I do not recommend this unless you have a set of "gunsmith" flat blade screwdrivers that exactly fit the sideplate screws and you know what you are doing. These screws are easily damaged. These internal parts are lubed at the factory and should last the life of the gun.
If you get the gun wet or in a humid enviorment often, you may want get the internal parts oiled but in normal use mine all have been fine the way they came for 15 years or so.
|
|
|
|
|
ree
|
Post subject: Posted: Mon Oct 06, 2008 11:05 am |
|
Longtime Regular |
|
Joined: Sun Apr 29, 2007 9:55 pm Posts: 742 Location: Twin Cities
|
mnglocker wrote: If you're shooting alot of lead you will need to clean the leading on the front of the cylinder...
A rubber pencil eraser does a great job of removing most of this really stubborn buildup.
|
|
|
|
|
plblark
|
Post subject: Posted: Mon Oct 06, 2008 11:07 am |
|
Longtime Regular |
|
Joined: Thu Mar 16, 2006 10:41 am Posts: 4468
|
you learn something EVERY day. I would never have thought of that. Thanks.
_________________ Certified Carry Permit Instructor (MNTactics.com and ShootingSafely.com) Click here for current Carry Classes "There is no safety for honest men, except by believing all possible evil of evil men." - Edwin Burke
|
|
|
|
|
rrpilot
|
Post subject: Tips Posted: Tue Oct 07, 2008 10:05 am |
|
Joined: Sun Sep 07, 2008 11:17 pm Posts: 9 Location: Burnsville
|
Thanks for all the tips!
_________________ Don't Panic
|
|
|
|
|
|
Page 1 of 1
|
[ 9 posts ] |
|
This is a static archive the Twin Cities Carry forum, maintained as a public service by the current forum of record, The Minnesota Carry Forum.
All times are UTC - 6 hours
Users browsing this forum: No registered users and 11 guests |
|
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum
|